ZX-E

Intelligente induktive Messsensoren

Die Familie ZX-E stellt die beste Lösung für die exakte Messung von Metallobjekten dar Diese Sensoren empfehlen sich insbesondere für den Einsatz unter widrigen Umgebungsbedingungen wie beispielsweise in der Automobil- oder metallverarbeitenden Industrie.

Hohe Auflösung: 1 µm
Kurze Ansprechzeit: 150 µs
Problemloser Austausch des Sensorkopfs
Modulares Plattformkonzept für unterschiedliche Erfassungstechnologien
Einfache Linearitätsanpassung für beliebige Metalle

Alle Modelle vergleichen CAD Zeichnungen

Spezifikationen & Bestellinfo

Ordering information

Sensors

Sensor heads

Shape	Dimensions	Sensing distance	Resolution 1 1. For an average count of 4,096.	Order code
Cylindrical	3 dia. × 18 mm	0.5 mm	1 μm	ZX-EDR5T
	5.4 dia. × 18 mm	1 mm		ZX-ED01T 2 2. Models with protective spiral tubes are also available. Add a suffix of “-S” to the above model numbers when ordering. (Example: ZX-ED01T-S)
	8 dia. × 22 mm	2 mm		ZX-ED02T 2 2. Models with protective spiral tubes are also available. Add a suffix of “-S” to the above model numbers when ordering. (Example: ZX-ED01T-S)
Screw-shaped	M10×22 mm	2 mm		ZX-EM02T 2 2. Models with protective spiral tubes are also available. Add a suffix of “-S” to the above model numbers when ordering. (Example: ZX-ED01T-S)
Screw-shaped	M18×46.3 mm	7 mm		ZX-EM07MT 2 2. Models with protective spiral tubes are also available. Add a suffix of “-S” to the above model numbers when ordering. (Example: ZX-ED01T-S)
Flat	30×14×4.8 mm	4 mm		ZX-EV04T 2 2. Models with protective spiral tubes are also available. Add a suffix of “-S” to the above model numbers when ordering. (Example: ZX-ED01T-S) , 3 3. Be sure to use ZX-EDA amplifier unit version 1,200 or later with the ZX-EV04.
Heat-resistant, cylindrical	M12×22 mm	2 mm		ZX-EM02HT 4 4. Be sure to use ZX-EDA amplifier unit version 1,300 or later with the ZX-EM02H.

Amplifier units

Power supply	Output type	Order code
DC	NPN	ZX-EDA11
DC	PNP	ZX-EDA41

Note: Compatible connection with the sensor head.

Accessories (order separately)

Calculating unit

	Model
Calculating unit	ZX-CAL2

Amplifier mounting brackets

Remarks	Model
Attached to each sensor head	ZX-XBE1
For DIN track mounting	ZX-XBE2

SmartMonitor sensor setup tool for Personal Computer connection

Name	Model
ZX-series communications interface unit	ZX-SF11
ZX-series communications interface unit + setup software (CD-ROM)	ZX-SFW11EV3 5 5. The ZX-SFW11EV3 SmartMonitor can be used only to set functions and monitor waveforms.
ZX-series sensor setup and logging software (CD-ROM)	ZX-SW11EV3

Name

Model

ZX-series communications interface unit

ZX-SF11

ZX-series communications interface unit

+ setup software (CD-ROM)

ZX-SFW11EV3

ZX-series sensor setup and logging software (CD-ROM)

ZX-SW11EV3

Cables with connectors on both ends (for extension)
*

undefined

Cable length	Model
1 m	ZX-XC1A
4 m	ZX-XC4A
8 m	ZX-XC8A

* Robot cable models are also available. The model numbers are ZX-XC_R.

Specifications

Sensor heads

Item			ZX-EDR5T	ZX-ED01T	ZX-ED02T/EM02T	ZX-EM07MT	ZX-EV04T	ZX-EM02HT
Measurement range			0 to 0.5 mm	0 to 1 mm	0 to 2 mm	0 to 7 mm	0 to 4 mm	0 to 2 mm
Sensing object			Magnetic metals (Measurement ranges and linearities are different for non-magnetic metals. Refer to engineering data on B-67.)
Standard reference object			18 × 18 × 3 mm		30 × 30 × 3 mm	60 × 60 × 3 mm		45 × 45 × 3 mm
Standard reference object			Material: Ferrous (S50C)
Resolution 6 6. Accuracy: The resolution is the deviation ( ±3 σ) in the linear output when connected to the ZX-EDA amplifier unit. The above values indicate the deviations observed 30 minutes after the power is turned ON. (The resolution is measured with Omron's standard reference object at ½ of the measurement range with the ZX-EDA set for the maximum average count of 4,096 per period.) The resolution is given at the repeat accuracy for a stationary workpiece, and is not an indication of the distance accuracy. The resolution may be adversely affected under strong electromagnetic fields.			1 µm
Linearity 7 7. Linearity: The linearity is given as the error in an ideal straight line displacement output when measuring the standard reference object. The linearity and measurement values vary with the object being measured.			±0.5% F.S.					±1% F.S. 8 8. The value given is for an ambient temperature of 25°C.
Linear output range			Same as measurement range.
Temperature characteristic 9 9. Temperature characteristic: The temperature characteristic is measured with Omron's standard reference object at ½ of the measurement range. (including amplifier unit)			0.15 % F.S./°C	0.07% F.S./°C				0.1% F.S./°C
Ambient temperature	Operating 10 10. The ambient temperature given is only for the sensor head. It is -10 to 60°C for the preamp.		0 to 50°C (with no icing or condensation)	-10 to 60°C (with no icing or condensation)				-10 to 200°C
Ambient temperature	Storage 5 10. The ambient temperature given is only for the sensor head. It is -10 to 60°C for the preamp.		0 to 50°C (with no icing or condensation)	-20 to 70°C (with no icing or condensation)				-20 to 200°C
Ambient humidity			Operating and storage: 35% to 85% (with no condensation)
Insulation resistance			50 MΩ min. (at 500 DC)
Dielectric strength			1,000 VAC, 50/60 Hz for 1 min between charged parts and case
Vibration resistance (destruction)			10 to 55 Hz with 1.5-mm double amplitude for 2 h each in X, Y, and Z directions
Shock resistance (destruction)			500 m/s2, 3 times each in X, Y, and Z directions
Degree of protection (sensor head)			IEC60529, IP65	IEC60529, IP67				IEC60529, IP60 11 11. Do not use in moist environments because the case is not waterproof.
Connection method			Connector relay (standard cable length: 2 m)
Weight (packed state)			Approx. 120 g	Approx. 140 g		Approx. 160 g	Approx. 130 g	Approx. 160 g
Materials	Sensor head	Case	Brass	Stainless steel	Brass		Zinc (nickel-plated)	Brass
	Sensor head	Sensing surface	Heat-resistant ABS					PEEK
	Preamplifier		PES
Accessories			Amplifier mounting brackets (ZX-XBE1), instruction manual

Amplifier units

Item	ZX-EDA11	ZX-EDA41
Measurement period	150 µs
Possible average count settings 12 12. The response speed of the linear output is calculated as the measurement period x (average count setting + 1) (with fixed sensitivity). The response speed of the judgement outputs is calculated as the measurement period x (average count setting + 1) (with fixed sensitivity).	1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1,024, 2,048, or 4,096
Linear output 13 13. The output can be switched between a current output and voltage output using a switch on the bottom of the amplifier unit.	Current output: 4 to 20 mA/F.S., max. load resistance: 300 Ω Voltage output: ±4 V (±5 V, 1 to 5 V 14 14. Setting is possible via the monitor focus function. ), output impedance: 100 Ω
Judgement outputs (3 outputs: HIGH/PASS/LOW)	NPN open-collector outputs, 30 VDC, 50 mA max. Residual voltage: 1.2 V max.	PNP open-collector outputs, 30 VDC, 50 mA max. Residual voltage: 2 V max.
Zero reset input, timing input, reset input, judgement output hold input	ON: Short-circuited with 0-V terminal or 1.5 V or less OFF: Open (leakage current: 0.1 mA max.)	ON: Supply voltage short-circuited or supply voltage within 1.5 V OFF: Open (leakage current: 0.1 mA max.)
Function	Measurement value display set value/output value/ resolution display Linearity adjustment (materials selection) Scaling Display reverse display OFF mode ECO mode Number of display digit changes sample hold peak hold Bottom hold, peak-to-peak hold self-peak hold self-bottom hold Average hold delay hold zero reset Initial reset linearity initialization ON-delay timer OFF-delay timer one-shot timer previous value comparison Non-measurement setting direct threshold value setting position teaching Automatic teaching hysteresis width setting timing inputs Reset input judgement output hold input monitor focus Linear output correction (A-B) calculations 4 15. A calculating unit (ZX-CAL or ZX-CAL2) is required. (A+B) calculations 15 15. A calculating unit (ZX-CAL or ZX-CAL2) is required. K-(A+B) calculation 4 15. A calculating unit (ZX-CAL or ZX-CAL2) is required. mutual interference prevention 4 15. A calculating unit (ZX-CAL or ZX-CAL2) is required. Sensor disconnection detection zero reset memory zero reset indicator Key lock
Indications	Judgement indicators: High (orange), pass (green), low (yellow), 7-segment main digital display (red), 7-segment sub-digital display (yellow), power ON (green), zero reset (green), enable (green)
Voltage influence (including sensor)	0.5% F.S. of linear output value at ±20% of power supply voltage
Power supply voltage	12 to 24 VDC ± 10%, ripple (p-p): 10% max.
Current consumption	140 mA max. with power supply voltage of 24 VDC (with sensor connected)
Ambient temperature	Operating and storage: 0 to 50°C (with no icing or condensation)
Ambient humidity	Operating and storage: 35% to 85% (with no condensation)
Insulation resistance	20 MΩ min. (at 500 DC)
Dielectric strength	1,000 VAC, 50/60 Hz for 1 min
Vibration resistance (destruction)	10 to 150 Hz with 0.7-mm double amplitude for 80 min each in X, Y, and Z directions
Shock resistance (destruction)	300 m/s2, 3 times each in 6 directions (up, down, left, right, forward, backward)
Connection method	Prewired (standard cable length: 2 m)
Weight (packed state)	Approx. 350 g
Materials	Case: PBT (polybutylene terephthalate), cover: Polycarbonate
Accessories	Instruction manual

1. For an average count of 4,096.

2. Models with protective spiral tubes are also available. Add a suffix of “-S” to the above model numbers when ordering. (Example: ZX-ED01T-S)

3. Be sure to use ZX-EDA amplifier unit version 1,200 or later with the ZX-EV04.

4. Be sure to use ZX-EDA amplifier unit version 1,300 or later with the ZX-EM02H.

5. The ZX-SFW11EV3 SmartMonitor can be used only to set functions and monitor waveforms.

6. Accuracy: The resolution is the deviation ( ±3 σ) in the linear output when connected to the ZX-EDA amplifier unit. The above values indicate the deviations observed 30 minutes after the power is turned ON.
(The resolution is measured with Omron's standard reference object at ½ of the measurement range with the ZX-EDA set for the maximum average count of 4,096 per period.)
The resolution is given at the repeat accuracy for a stationary workpiece, and is not an indication of the distance accuracy. The resolution may be adversely affected under strong electromagnetic fields.

7. Linearity: The linearity is given as the error in an ideal straight line displacement output when measuring the standard reference object. The linearity and measurement values vary with the object being measured.

8. The value given is for an ambient temperature of 25°C.

9. Temperature characteristic: The temperature characteristic is measured with Omron's standard reference object at ½ of the measurement range.

10. The ambient temperature given is only for the sensor head. It is -10 to 60°C for the preamp.

11. Do not use in moist environments because the case is not waterproof.

12. The response speed of the linear output is calculated as the measurement period x (average count setting + 1) (with fixed sensitivity).
The response speed of the judgement outputs is calculated as the measurement period x (average count setting + 1) (with fixed sensitivity).

13. The output can be switched between a current output and voltage output using a switch on the bottom of the amplifier unit.

14. Setting is possible via the monitor focus function.

15. A calculating unit (ZX-CAL or ZX-CAL2) is required.

1. For an average count of 4,096.

2. Models with protective spiral tubes are also available. Add a suffix of “-S” to the above model numbers when ordering. (Example: ZX-ED01T-S)

3. Be sure to use ZX-EDA amplifier unit version 1,200 or later with the ZX-EV04.

4. Be sure to use ZX-EDA amplifier unit version 1,300 or later with the ZX-EM02H.

5. The ZX-SFW11EV3 SmartMonitor can be used only to set functions and monitor waveforms.

8. The value given is for an ambient temperature of 25°C.

9. Temperature characteristic: The temperature characteristic is measured with Omron's standard reference object at ½ of the measurement range.

10. The ambient temperature given is only for the sensor head. It is -10 to 60°C for the preamp.

11. Do not use in moist environments because the case is not waterproof.

13. The output can be switched between a current output and voltage output using a switch on the bottom of the amplifier unit.

14. Setting is possible via the monitor focus function.

15. A calculating unit (ZX-CAL or ZX-CAL2) is required.

Wie können wir Ihnen helfen?

Wenn Sie eine Frage haben oder ein Angebot anfordern möchten, kontaktieren Sie uns oder senden Sie eine Anfrage.

+49 (0)21 73 - 68 00 0

Ihr Kontakt ZX-E

Bitte füllen Sie alle Felder aus, die diese * Markierung besitzen. Ihre persönlichen Daten werden natürlich vertraulich behandelt.

Name

Text error notification

Nachname

Text error notification

E-Mail-Adresse

Email error notification

Telefon

Text error notification

Unternehmen

Text error notification

Postleitzahl

Text error notification

Land

Frage oder Anmerkung

Text area error notification

Ich bin einverstanden mit OMRON Privacy Policy

Checkbox error notification

Den Newsletter abonnieren

Checkbox error notification

Vielen Dank für Ihre Anfrage. Wir setzen uns umgehend mit Ihnen in Verbindung.

Es liegen zur Zeit technische Probleme vor. Ihre Übertragung war nicht erfolgreich. Entschuldigen Sie dies bitte und versuchen es später noch einmal. Details

Download

+49 (0)21 73 - 68 00 0

Angebot anfordern

Angebot für ZX-E

Über dieses Formular erhalten Sie ein Angebot zu Ihrem ausgewählten Produkt. Bitte füllen Sie alle Felder aus, die diese * Markierung besitzen. Ihre persönlichen Daten werden natürlich vertraulich behandelt.

Persönliche Daten

Produkt ZX-E

Name

Text error notification

Nachname

Text error notification

E-Mail-Adresse

Email error notification

Telefon

Text error notification

Titel/Position

Text error notification

Unternehmen

Text error notification

Unternehmenswebsite

Text error notification

Strasse

Text error notification

Stadt

Text error notification

Postleitzahl

Text error notification

Land

Angebotsdetails

Art der Anfrage

Stückzahl

Numeric error notification

Kaufen Sie bei Omron oder bei einem Vertriebspartner?

Erzählen Sie uns etwas über Ihr Projekt

Text area error notification

Ich bin einverstanden mit OMRON Privacy Policy

Checkbox error notification

Den Newsletter abonnieren

Checkbox error notification

Vielen Dank für Ihre Angebots-Anfrage, die wir schnellstmöglich beantworten werden.

Es liegen zur Zeit technische Probleme vor. Ihre Übertragung war nicht erfolgreich. Entschuldigen Sie dies bitte und versuchen es später noch einmal. Details

Download

Angebot anfordern